The paper contains a sensitivity analysis of the influence of uncertainties in input hydrological, morphological and operating data required for a proposal for active reservoir conservation storage capacity and its achieved values. By introducing uncertainties into the considered inputs of the water management analysis of a reservoir, the subsequent analysed reservoir storage capacity is also affected with uncertainties. The values of water outflows from the reservoir and the hydrological reliabilities are affected with uncertainties as well. A simulation model of reservoir behaviour has been compiled with this kind of calculation as stated below. The model allows evaluation of the solution results, taking uncertainties into consideration, in contributing to a reduction in the occurrence of failure or lack of water during reservoir operation in low-water and dry periods.
Safe and effective loading of nuclear reactor fuel assemblies demand qualitative and quantitaive analysis of the relations between the coolant temperature in the fuel assembly outlet, measured by a thermocouple, and the mean temperature of the coolant in the thermocouple plane position. In the laboratory at the Institute of Thermal Power Engineering of the Slovak University of Technology in Bratislava, an experiemental physical fuel assembly model of the VVER 440 nuclear power plant with V 213 nuclear reactors was installed The aim of the measurements on the physical model was to analyze the temperature and velocity profiles in the fuel assembly outlet. The following article deals with the analyses of these measurements based on different mass flow of the water through a physical model of the fuel assembly outlet. The following arficle deals with the analysis of these measurements based on different discontinuity generated by cold water flowing through triplet tubes and central tube in plane 1, and the positioning of the mixing CFD grid simulations of a fuel assembly outlet. All analyses were validated by means of measurements on the physical model of the fuel assembly. and Obsahuje seznam literatury
Time series of the daily total precipitation, daily wastewater discharges and daily concentrations and pollution loads of BOD5, COD, SS, N-NH4, Ntot and Ptot were analyzed at the inflow to the wastewater treatment plant (WWTP) for a larger city in 2004-2009 (WWTP is loaded by pollution from 435,000 equivalent inhabitants). The time series of the outflow from a WWTP was also available for 2007. The time series of daily total precipitation, daily wastewater discharges, concentrations and pollution loads at the inflow and outflow from the WWTP were standardized year by year to exclude a long-term trend, and periodic components with a period of 7 days and 365 days (and potentially also 186.5 days) were excluded from the standardized series. However, these two operations eliminated only a small part of the variance; there was a substantial reduction in the variance only for ammonium nitrogen and total nitrogen at the inflow and outflow from a WWTP. The relationship between the inflow into a WWTP and the outflow from a WWTP for the concentrations and pollution loads was described by simple transfer functions (SISO models) and more complicated transfer functions (MISO models). A simple transfer function (SISO model) was employed to describe the relationship between the daily total precipitation and the wastewater discharge.
The article deals with the posssibility of using different design techniques of centrifugal pumps designing in the context of their use in the computer-aided design. It is carried out a comparison of calculated and experimental pump characteristics. and Obsahuje seznam literatury
High temperature alters the internal microstructure of rocks and consequently changes the physical and mechanical properties of rocks. Many studies have been carried out to examine the transformations in the microstructures of rocks under high temperature through near infrared spectroscopy (NIR), Raman spectroscopy, or thermo gravimetric analysis (TGA). The current review synthesizes the data from a number of literatures and summarizes the major transformations of silica rocks under high temperature. The analysis shows that silica rocks starts to lose the water adsorbed in open pores upon heating at about 150 °C. At 200-300 °C, the reaction between SiOH (silanole) in the rocks generates new Si-O-Si bonds as well as H2O, and decreases the open pores. The rocks undergo volume expansion at >550 °C, and the volume contracts and forms new micro pores or cracks which play an important role in the evacuation of the water., Jishi Geng, Qiang Sun, Yuchun Zhang and Yuliang Zhang., and Obsahuje bibliografické odkazy
The previously developed thoracic finite element model [8, 9] was used to investigate the human thoracic dynamic responses associated with the frontal, lateral and oblique loading and to predict injuries of the thorax associated with the frontal loading. The thoracic model was developed [8, 9] to improve the human articulated rigid body model ROBBY (the model of an average adult male) [13, 14], which was previously developed at the University of West Bohemia in cooperation with ESI Group (Engineering Simulation for Industry). There are implemented deformable models of the thorax and abdomen in the ROBBY model. The geometries of individual thoracic organs were based on the cadaver tomography data and color cross-section photographs obtained from Visible Human Project (VHP) [33]. The thoracic model material properties were obtained either by virtue of cooperation with ESI Group or from public sources (articles, Internet, books). Thoracic model includes the models of the sternum, ribs, costal cartilages, vertebrae, lungs, heart, trachea, main vessels (aorta, vena cava superior), intercostal muscles, diaphragm, flesh and skin. The presented study deals with the dynamic response and validation of the whole thoracic model and with the prediction of thoracic injuries by virtue of this model. The results of simulations are compared with the experimental results. and Obsahuje seznam literatury
In this paper, we deal with sentences containing time references like ''five years ago'', ''three years older'', ''in five seconds''. It turns out that such sentences are pragmatically incomplete, because there is an elliptic reference to a calendar that makes it possible to determine the length of the time interval associated with a time duration like a year, month, day, or to compute the time interval denoted by terms like ''February 29, 2016''. Since Transparent Intensional Logic (TIL) takes into account two modal parameters, namely possible worlds of type ω and times of type τ, and this system is particularly apt for the analysis of natural language expressions, our background theory is TIL. Within this system, we define time intervals, calendar time durations, and last but not least a method for adding and multiplying time durations in a way that takes into account the leap days and leap seconds. As sample applications, we analyse two sentences, to wit, ''A year has 365 days'' and ''Adam is 5 years older than Bill''. and V tomto článku se zabýváme věty obsahujícími časové odkazy jako ''před pěti lety'', ''o tři roky starší'', ''za pět sekund''. Ukazuje se, že takové věty jsou pragmaticky neúplné, protože existuje eliptický odkaz na kalendář, který umožňuje určit délku časového intervalu spojeného s časovým obdobím jako rok, měsíc, den nebo vypočítat časový interval označované slovy ''29. února 2016''. Vzhledem k tomu, že Transparentní Intenzivní Logika (TIL) zohledňuje dva modální parametry, jmenovitě možné světy typu ω a časy typu τ, a tento systém je obzvláště vhodný pro analýzu přirozených jazykových výrazů, je naší teorií pozadí TIL. V rámci tohoto systému definujeme časové intervaly, trvání kalendáře, a v neposlední řadě metoda pro přidání a násobení doby trvání způsobem, který bere v úvahu skokové a skokové sekundy. Jako vzorové aplikace analyzujeme dvě věty s názvem ''rok má 365 dní'' a ''Adam je o 5 let starší než Bill''.
Persistent Scatterer Interferometry (PSI), a remote sensing technique, is used for detecting surface deformation in the cities of Prague and Ostrava. PSI is able to detect vertical movements with an accuracy of less than 1 mm for a long time series of the SAR data, but the maximum detectable rate of movement is only a few centimetres per year. This technique is quite suitable for detecting recent movements in most Prague localities. On the other hand, in Ostrava and its surroundings, affected by undermining, where subsidences (1992-2006) amount to decimetres per year, movements cannot be fully detected by the PSInSAR technique. The paper presents results of analysing PSI data for two localities in Prague and one locality in the Ostrava areas. The localities are strictly situated in built-up areas with many suitable reflectors. Data from the ERS-1/2 and ENVISAT satellites covering a 13-year period for the Prague (1992-2005) and a 14-year period for the Ostrava (1992-2006) area were used. Annual movement velocities and time-series of reflectors were determined. At these three localities, where different types of movements were identified, the application and possible limitations of PSI in urban areas are shown., Pavel Kadlečík, Vladimír Schenk, Zuzana Seidlová and Zdeňka Schenková., and Obsahuje bibliografii
The main objective of this paper is to explain how the application of various interpolation methods influence the determination of vertical crustal movements at any given point. The paper compares several methods of interpolation and verifies their suitability, including kriging, minimum curvature, nearest neighbor, natural neighbor, polynomial regression, inverse distance to a power, and triangulation with linear interpolation. The calculations show that the chosen interpolation method has significant influence on the final result of the study. Nearest neighbor method was chosen to be the best., Kamil Kowalczyk, Jacek Rapinski and Marek Mroz., and Obsahuje bibliografii
This paper proposes a non-trivial definition of the notion of analytic method. Working within the so-called instructional model of method, I distinguish three kinds of instructions which occur in methods: selective, executive, and declarative instructions. I discuss the relation between each of these and the analyticity of a method. Then I define the notions of an analytic use of an instruction and of an analytic instruction, which are at the basis of the proposed definition of an analytic method. Finally, I discuss the issue of circularity in the presented model which arises if we consider a finite agent testing a method for analyticity., Tato práce navrhuje netriviální definici pojmu analytická metoda. V rámci tzv. Instruktážního modelu metody rozlišuji tři druhy instrukcí, které se vyskytují v metodách: selektivní, exekutivní a deklarativní . Diskutuji o vztahu mezi každou z nich a analytičnosti metody. Dále definuji pojmy analytického použití instrukce a analytické instrukce , které jsou základem navrhované definice analytické metody. Závěrem se zabývám otázkou kruhovitosti v prezentovaném modelu, která vzniká, pokud uvažujeme konečný agent testující metodu analyticity., and Miloš Kosterec