3D microscopy and image analysis provide reliable measurements of length, branching, density, tortuosity and orientation of tubular structures in biological samples. We present a survey of methods for analysis of large samples by measurement of local differences in geometrical characteristics. The methods are demonstrated on the structure of the capillary bed in a rat brain., J. Janáček ... [et al.]., and Obsahuje bibliografii a bibliografické odkazy
The present paper concerns long-term 3D monitoring of active fault structures in the Krupnik-Kresna seismic zone, SW Bulgaria with the use of extensometers TM71. The purpose is to establish the real rates of fault movements in the most seismically active area in Bulgaria. Three points were installed (B6 on Krupnik Fault, and K5 and K12 on Struma Fault), which indicate a recent activity. The fault movements are characteristic with “calm” periods, linear slips, accelerations and sudden displacements. Different regimes of dynamics have been established corresponding to different periods. The greatest dynamics is found at monitoring point B6 along Krupnik Fault: for the whole period of observation the trends are calculated as left lateral slip with 1.88 mm/a and a thrusting with 1.59 mm/a with high correlation coefficients. Co-seismic displacements from local and distant earthquakes were recorded. The significant impact was from M=7.4, 17 August, 1999, Izmit Earthquake, Turkey, showing a shortening of 8.34 mm, a right-lateral slip of 5.09 mm and a thrusting of 0.96 mm. After that, for a short period of time the regime of movement on fault was changed. Movements on the Struma system reveal lower rates. Both points show left-lateral movements, 0.28 mm/a at K5 and 0.09 mm/a at K12, and thrusting with 0.11 mm/a at K5 and 0.72 mm/a at K12., Nikolai Dobrev., and Obsahuje bibliografii
The present paper shows the results of 3D monitoring with the use of extensomet ers TM71 performed in Bulgaria in the framework of COST Action 625. This research was performed in selected areas: Simitli graben that is the most seismoactive area in Bulgaria; Madara plat eau - rock scarp with historical monument affe cted by rock toppling; East Rhodopes area - a possibly active fault zone and a large landslide. The most impressive results were established at Simitli graben area with the rate of 2.73 mm/year sinistral movement of Krupnik Fault. Local earthquakes located at NE part of the graben usually influence the movements along this fault. An acceleration of the left latera l movements during calm periods has been established, and respectively, the movements stop (or going in opposite direction) during seismic activity. At Madara site, the results from the 15 years monitoring show subsidence of rock s lices by 0.9 mm per year and si milar rate movement of the slices to South direction. Influence from Izmit earthquake, Vrancea earthquakes and local ones have been established. The monitoring of the fault at General Geshe vo Village, East Rhodopean area started in 2003. The first results show mainly gravitational movements - subsidence of NE block 1.5 mm/year., Nikolai Dobrev and Elka Avramova-Tacheva., and Obsahuje bibliografické odkazy
The paper presents the results of geodyn amic research in the fram e of the project COST 625 relating to active tectonic structures’ monitoring on the selected areas in Poland, Italy and Greece. Research was realised using a self-developed control and measurement system. The resu lts of researches for period 2000-2006 indi cate slight movements of observatio n points in the Sudety Mts. reaching several millimetres. However, the results confirm recent mobility of tectonic structures o f this area. Research realised in the Mediterranean Region objects - Gargano, Norcia (Italy) and Kaparelli (Greece) - indicate movements of observation points reaching over a dozen millimetres, particularly on the Gargano area. Continuation of cyclic control measurements on these objects is fully justified ., Stefan Cacoń, Bernard Kontny and Jarosław Bosy., and Obsahuje bibliografické odkazy
This paper presents a new approach to 3D object recognition by using an Octree model library (OML) I, II and fast search algorithm. The fast search algorithm is used for finding the 4 pairs of feature points to estimate the viewing direction uses on effective two level database. The method is based on matching the object contour to the reference occluded shapes of 49, 118 viewing directions. The initially bestmatched viewing direction is calibrated by searching for the 4 pairs of feature points between the input image and the image projected along the estimated viewing direction. At this point, the input shape is recognized by matching it to the projected shape. The computational complexity of the proposed method is shown to be O(n^2) in the worst case, and that of the simple combinatorial method of O(m^4,n^2), where n and m denote the number of feature points of the 3D model object and the 2D object, respectively.