To obtain the starting point for theoretical numerical computations the fibre reinforced concrete construction properties, adhesion of cement mixture with steel and polypropylene fibres and changes in its tension properties commensurate with number and weight percentage in the tested specimen were tested under laboratory conditions., Jiřina Trčková and Karel Řezba., and Obsahuje bibliografické odkazy
Evaluation of seismic loading in urban areas is not a simple process. The horizontal to vertical spectral ratio method technique has been often used for determination of site effect recently. Results from the re-interpretation of mining induced seismic events from Karviná region in frequency domain using archival databases will be presented in this study material. Also, spectra of continuous records (a bout two days) and evolution of spectra within a moving time window of the length 10 seconds are presented. These continuous records were registered on two places with different geological conditions., Zdeněk Kaláb and Alexey A. Lyubushin., and Obsahuje bibliografické odkazy
Generally, rock material failure is controlled by cracks under specific conditions. The study of rock fracture toughness belongs to the current frequent directions of research in the area of rock failure. The present paper describes the effects of parameters influencing the resultant properties of rock materials (bending rate, rock moisture) during fracture toughness measurement of different kinds of rocks (sandstone, marble, granite). The highest fracture toughness values were found in the marble samples. This is probably due to the inner structure of analysed marble, which is composed of only one mineral (calcite) and also has a lower porosity than the used granite. The lowest fracture toughness values were found in the sandstone sample, and reached c. 17-30 % of the measured fracture toughness values of the analysed granite and marble samples. As in the case of the other mechanical properties of rocks (e.g. uniaxial compressive strength) also in the case of higher sandstone (carboniferous) moisture the fracture toughness values decrease and its deformation ability increases. Preparation of samples for fracture toughness tests and performance of these tests are more complicated than in the case of tensile tests (e.g. the Brazilian test) and therefore this contribution presents a comparison between fracture toughness of analysed rocks and tensile strength values. The measured data in this study considering the fracture toughness tests and Brazilian tests were compared with results published by Zhang (2002)., Leona Vavro and Kamil Souček., and Obsahuje bibliografii
Using the FLAC3D numerical simulation method, the characteristics of mining stress evolution, fault activation patterns, and fault energy evolution characteristics are simulated and analyzed in the process of the footwall and hanging wall working face heading to a normal fault. The study shows that the fault cut off the mining stress propagation of overlying strata, and the stress blocking effect due to the fault is evident. When working faces head towards a fault, the abutment pressure and the vertical stress of the surrounding rock increase first and subsequently decrease. The abutment pressure of the coal wall and fault is highest when the distances to the fault are 40 m and 30 m for the footwall and hanging wall working faces, respectively. Moreover, the hanging wall mining stress is higher than the footwall mining stress. Fault activation in high-located strata precedes that in low-located strata when working faces head towards the normal fault. Energy is gradually accumulated before unstable fault events take place because of mining, and fault instability quickly releases a lot of energy. The mining stress concentration and fault activation due to faults easily result in rock bursts and mine seismicity, Wu Quan-sen, Jiang Li-shuai and Wu Quan-lin., and Obsahuje bibliografické odkazy
The Hronov-Poříčí Trough represents the easternmost part of the Trutnov-Náchod Depression. The NW-SE striking structure was formed due to the post-Cretaceous flexural folding and is filled with the Upper Cretaceous sediments. Both the NE and SW margins of the trough are bounded by flexures with the Upper Cretaceous strata dipping 40-60° towards the axis of the trough. The NE flexure is situated close to the parallel Hronov-Poříčí Fault Zone. Up to now, it is not fully known, in what extent the normal faulting was involved in the evolution of the structure. From the geomorphological point of view, the normal fault constraints of the trough seem to be acceptable, as the surface topography of its present margins exhibit many signs typical for fault scarps. However, the existence of a fault system bounding all round the Hronov-Poříčí Trough has not b een proved by any geological research. Hence the geophysical research was carried out on both sides of the NW part of the trough to support one of these hypothesis. Five geoelectrical profiles were measured in the area and the fault system was proved on the NE side of the trough. On the SW boundary the fault system was not found. Thus it seems, that the NE boundary is controlled by fault tectonics, whereas the SW boundary is rather formed by a simple flexure., Jan Valenta, Vladimír Stejskal and Petra Štěpančíková., and Obsahuje bibliografické odkazy
In the frame of advanced studies of coal structure the temperature conditions of coal origin were investigated through thermal stability of aluminum complexes in coal substance. These compounds were discovered by solid-state nuclear magnetic resonance measurements of 27Al as a part of coal substance closely bonded to organic mass of coal. In obtained spectra, Al-hexaphenoxide and Al-tetrahydroxy-diphenoxide complexes were identified. These complexes were further prepared and their thermal stability tested by thermal analysis method. It was found that a) they can originate under room temperature and atmospheric pressure and b) they are thermally stable only up to approximately 85 or 95 °C. As both Al-hexaphenoxide and Al-tetrahydroxy-diphenoxide complexes are the integrated constituents of coal substance it can be deduced that, in the beginning, coal was formed under very mild thermal conditions. As investigated materials, coals and clays from the Czech basins and gagatite from Poland were measured., Pavel Straka and Jana Náhunková., and Obsahuje bibliografii